This manual is only for Lite FC board with LiteSilver firmware.
How to update firmware for Lite Brushed V2 board
The MCU chip is STM32F042 for this brushed FC board. So we use the DFU mode to re-flash the firmware. There are no bootloader in this firmware.
- Press and hold the button at the bottom of the flight control, and then plug in the USB. At this time, only the power led is on (red led). In this step, the original firmware will be removed.
- Switch to Configurator’s Flasher page, choose Brushed tab, Click the Load Firmware [Local], and load the firmware via the Open File button.
- Then click the Find DFU devices button to find the DFU port. The FC should be loading as STM32 BOOTLOADER device, not STM Device in DFU Mode. We could use the Zadig to replace device driver if needed.
- If DFU device is found successfully, just click the Flash Firmware button to re-flash the firmware.
How to update firmware for Lite 1-2S Brushless board
The MCU chip is MM32F103 for this brushless board. There is a bootloader in this firmware. We could re-flash the firmware with the help of this bootloader.
- Press and hold the button at the bottom of the flight control, and then plug in the USB. At this time, only the power led is on (red led).
- Switch to Configuration’s Flasher page, click Local, and load the firmware via the Open File button.
- In the Communication Area, select the serial port number corresponding to the flight control and connect.
- When the progress bar is complete, disconnect the USB and the update is complete.
Note: You do not need to connect flight control on the setup page to update the firmware.
Note: It is necessary to rebind after firmware update.
Note: Updating the firmware does not erase the bootloader, so don’t worry if the update fails, try a few more times.
Configurator and Device Driver
If you use a Windows 32bit system, download this Configurator.
https://drive.google.com/file/d/1bxTUu4FvIjzG2-jKNCxqsIbwB51IXepG/view?usp=sharing
If you use a Windows 64bit system, dowload this Configurator.
https://drive.google.com/file/d/1sKVWLeqyRohyg0D4PYMJcyOi3W5miAaD/view?usp=sharing
Zadig Device Driver
Lite Brushed FC V2 Firmware
If you use the integrated Bayang receiver, use the firmware below.
The FC board in BETAFPV Starter Kit 2 should use this firmware.
https://drive.google.com/file/d/1qBpKc-UkxwMN4rJrxtiqiw8yI-ShcYqt/view?usp=sharing
If you use a external receiver via the SBUS port, use the firmware below.
https://drive.google.com/file/d/1wuUBjp-l2Rf1WMxZ1oEmTqYfWgauNjm5/view?usp=sharing
Lite 1-2S Brushless FC Firmware
comming soon
Comments
11 comments
where can i get the old 'Lite Brushed FC V2 Firmware'?
though i enter the ADVANCED mode ,i still can't change PID values in the new firmware!!!!!
When will you upload formware for Lite 1-2S Brushless FC?
I really need it to unbrick my Meteor75 whit this FC.
My drone from Advance Kit 2 is not working properly, the OSD is always blinking and showing wrong info while flying. Is there any way to update the firmware of the FC?
Hi Jordali! I had the same problem with the drone from Advance Kit. I've tried to reflash before I understood that there is no file on the site.
Hi everyone who comes here to find firmware for Lite 1-2S Brushless FC. You could find it here:
https://betafpv.github.io/2020/11/LiteSilver_en/
@xiyiji
Hi Sir, the 'Lite Brushed FC V2 Firmware' has been updated. Please check.
How to setting the 'Lite Brushed FC V3' ? Can you help me? Cause i wan to change my PID.
How to setting the 'Lite Brushed FC V3' ? Can you help me? Cause i wan to change my PID.
What about updates for Lite 1-2S Brushless FC Firmware ?
Do you have any plans to post the firmware?
Can you add firmware and user manual for 'Lite Brushed FC V3' please? I can't get it working.
can someone please help i dont have the STM32 BOOTLOADER
Please sign in to leave a comment.