Entering CLI Mode, type 'exit' 

# diff all

# version
# Betaflight / STM32G47X (G473) 2025.12.5-alpha Jun 25 2026 / 03:24:50 (eb2bb5a33) MSP API: 1.47
# config rev: 1359bbe

# start the command batch
batch start

# reset configuration to default settings
defaults nosave

board_name BETAFPVG473
manufacturer_id BEFH
mcu_id 001d001f3235511235363938
signature 

# name: Meteor65 Pro

# feature
feature TELEMETRY
feature LED_STRIP
feature OSD

# serial
serial UART2 0 115200 57600 0 115200
serial UART4 131073 115200 57600 0 115200

# beacon
beacon RX_LOST
beacon RX_SET

# aux
aux 0 0 0 1700 2100 0 0
aux 1 1 1 900 1300 0 0
aux 2 2 1 1300 1700 0 0
aux 3 13 3 1700 2100 0 0
aux 4 35 2 1700 2100 0 0

# master
set gyro_lpf1_static_hz = 0
set gyro_lpf2_static_hz = 600
set dyn_notch_count = 1
set dyn_notch_q = 450
set dyn_notch_min_hz = 120
set gyro_lpf1_dyn_min_hz = 0
set acc_calibration = 29,44,-12,1
set baro_hardware = NONE
set dshot_bidir = ON
set dshot_bitbang = AUTO
set motor_pwm_protocol = DSHOT300
set motor_poles = 12
set align_board_yaw = -90
set vbat_max_cell_voltage = 440
set vbat_warning_cell_voltage = 345
set ibata_scale = 550
set ibata_offset = -100
set small_angle = 180
set simplified_gyro_filter_multiplier = 120
set osd_rssi_dbm_alarm = -99
set osd_vbat_pos = 2563
set osd_rssi_pos = 192
set osd_link_quality_pos = 2498
set osd_rssi_dbm_pos = 2467
set osd_rsnr_pos = 160
set osd_tim_1_pos = 386
set osd_tim_2_pos = 3628
set osd_remaining_time_estimate_pos = 33
set osd_flymode_pos = 3597
set osd_throttle_pos = 3565
set osd_vtx_channel_pos = 33
set osd_crosshairs_pos = 2360
set osd_current_pos = 2594
set osd_mah_drawn_pos = 577
set osd_craft_name_pos = 2581
set osd_home_dist_pos = 98
set osd_flight_dist_pos = 130
set osd_warnings_pos = 14837
set osd_avg_cell_voltage_pos = 44
set osd_pit_ang_pos = 97
set osd_rol_ang_pos = 65
set osd_disarmed_pos = 267
set osd_esc_tmp_pos = 129
set osd_esc_rpm_pos = 150
set osd_core_temp_pos = 225
set craft_name = Meteor65 Pro

profile 0

# profile 0
set profile_name = GF 1409
set dterm_lpf1_dyn_min_hz = 82
set dterm_lpf1_dyn_max_hz = 165
set dterm_lpf1_static_hz = 82
set dterm_lpf2_static_hz = 165
set throttle_boost = 0
set i_pitch = 79
set d_pitch = 37
set f_pitch = 99
set p_roll = 35
set i_roll = 60
set d_roll = 25
set f_roll = 76
set p_yaw = 35
set i_yaw = 60
set f_yaw = 76
set d_max_roll = 27
set d_max_pitch = 41
set auto_profile_cell_count = 1
set feedforward_smooth_factor = 60
set feedforward_jitter_factor = 12
set dyn_idle_min_rpm = 30
set simplified_master_multiplier = 80
set simplified_i_gain = 95
set simplified_d_gain = 105
set simplified_d_max_gain = 30
set simplified_feedforward_gain = 80
set simplified_pitch_d_gain = 130
set simplified_pitch_pi_gain = 125
set simplified_dterm_filter_multiplier = 110
set tpa_rate = 70

profile 1

profile 2

profile 3

# restore original profile selection
profile 0

rateprofile 0

rateprofile 1

rateprofile 2

rateprofile 3

# restore original rateprofile selection
rateprofile 0

# save configuration
save
#