# diff all # version # Betaflight / BETAFPVF4SX1280 (BHER) 4.3.0 Nov 3 2021 / 15:43:00 (0265565fa) MSP API: 1.44 # start the command batch batch start # reset configuration to default settings defaults nosave board_name BETAFPVF4SX1280 mcu_id 002d001f3236510435383430 signature # name: HX115 LR-ELRS # serial serial 30 2048 115200 57600 0 115200 # led led 0 0,0::A:0 led 1 1,0::A:0 # aux aux 0 0 0 1600 2100 0 0 aux 1 1 1 900 1300 0 0 aux 2 2 1 1325 1700 0 0 aux 3 13 3 1700 2100 0 0 aux 4 35 2 1550 2100 0 0 # vtxtable vtxtable bands 5 vtxtable channels 8 vtxtable band 1 BOSCAM_A A FACTORY 5865 5845 5825 5805 5785 5765 5745 5725 vtxtable band 2 BOSCAM_B B FACTORY 5733 5752 5771 5790 5809 5828 5847 5866 vtxtable band 3 BOSCAM_E E FACTORY 5705 5685 5665 5645 5885 5905 5925 5945 vtxtable band 4 FATSHARK F FACTORY 5740 5760 5780 5800 5820 5840 5860 5880 vtxtable band 5 RACEBAND R FACTORY 5658 5695 5732 5769 5806 5843 5880 5917 vtxtable powerlevels 4 vtxtable powervalues 0 1 2 3 vtxtable powerlabels 25 100 200 350 # master set dyn_notch_max_hz = 500 set acc_calibration = -59,29,96,1 set max_check = 2000 set dshot_idle_value = 700 set motor_pwm_protocol = DSHOT600 set yaw_motors_reversed = ON set small_angle = 180 set osd_vbat_pos = 2391 set osd_rssi_pos = 2276 set osd_link_quality_pos = 2244 set osd_rssi_dbm_pos = 2212 set osd_tim_2_pos = 2403 set osd_flymode_pos = 2371 set osd_crosshairs_pos = 2253 set osd_current_pos = 2422 set osd_craft_name_pos = 2410 set osd_core_temp_pos = 2230 set vtx_band = 4 set vtx_channel = 4 set vtx_power = 3 set vtx_freq = 5800 set expresslrs_uid = 240,8,174,153,199,40 set expresslrs_rate_index = 1 set expresslrs_hybrid_switches = ON set name = HX115 LR-ELRS profile 0 # profile 0 set p_pitch = 92 set i_pitch = 117 set d_pitch = 94 set f_pitch = 87 set p_roll = 89 set i_roll = 111 set d_roll = 90 set f_roll = 82 set p_yaw = 88 set i_yaw = 117 set f_yaw = 82 set d_min_roll = 0 set d_min_pitch = 0 profile 1 profile 2 # restore original profile selection profile 0 rateprofile 0 rateprofile 1 rateprofile 2 rateprofile 3 rateprofile 4 rateprofile 5 # restore original rateprofile selection rateprofile 0 # save configuration set dshot_bitbang = OFF save