This Cli Diff can be used for betaflight_4.1.0_MATEKF411RX.hex on HX100 SE FPV Quad.

beacon RX_LOST
beacon RX_SET
serial 0 2048 115200 57600 0 115200
aux 0 0 0 1700 2100 0 0
aux 1 1 1 1300 1700 0 0
aux 2 2 2 1700 2100 0 0
aux 3 35 2 1700 2100 0 0
vtxtable bands 5
vtxtable channels 8
vtxtable band 1 BOSCAM_A A FACTORY 5865 5845 5825 5805 5785 5765 5745 5725
vtxtable band 2 BOSCAM_B B FACTORY 5733 5752 5771 5790 5809 5828 5847 5866
vtxtable band 3 BOSCAM_E E FACTORY 5705 5685 5665 5645 5885 5905 5925 5945
vtxtable band 4 FATSHARK F FACTORY 5740 5760 5780 5800 5820 5840 5860 5880
vtxtable band 5 RACEBAND R FACTORY 5658 5695 5732 5769 5806 5843 5880 5917
vtxtable powerlevels 4
vtxtable powervalues 0 1 2 3
vtxtable powerlabels 25 200 500 800
set gyro_sync_denom = 2
set gyro_lowpass2_hz = 375
set dyn_lpf_gyro_min_hz = 300
set dyn_lpf_gyro_max_hz = 750
set mag_hardware = NONE
set baro_hardware = NONE
set rx_spi_protocol = FRSKY_X_LBT
set motor_pwm_protocol = DSHOT600
set motor_poles = 12
set vbat_max_cell_voltage = 440
set vbat_min_cell_voltage = 320
set vbat_warning_cell_voltage = 340
set yaw_motors_reversed = ON
set small_angle = 180
set osd_warn_core_temp = OFF
set osd_warn_rc_smoothing = OFF
set osd_warn_fail_safe = OFF
set osd_warn_launch_control = OFF
set osd_warn_no_gps_rescue = OFF
set osd_vbat_pos = 2433
set osd_rssi_pos = 2337
set osd_tim_2_pos = 2455
set osd_flymode_pos = 2424
set osd_throttle_pos = 2401
set osd_crosshairs_pos = 237
set osd_craft_name_pos = 2441
set osd_warnings_pos = 2409
set vcd_video_system = NTSC
set gyro_1_align_yaw = 1800
set name = HX-100 SE
set dyn_lpf_dterm_min_hz = 105
set dyn_lpf_dterm_max_hz = 255
set dterm_lowpass2_hz = 225
set vbat_pid_gain = ON
set p_pitch = 70
set i_pitch = 126
set d_pitch = 53
set f_pitch = 133
set p_roll = 64
set i_roll = 119
set d_roll = 49
set f_roll = 126
set p_yaw = 42
set i_yaw = 126
set f_yaw = 126
set d_min_roll = 28
set d_min_pitch = 31
set thr_mid = 40
set roll_rc_rate = 90
set pitch_rc_rate = 90
set yaw_rc_rate = 90
set roll_srate = 83
set pitch_srate = 83
set yaw_srate = 83
set tpa_rate = 25
set tpa_breakpoint = 1400
save